JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser.
Checkout using your account
This form is protected by reCAPTCHA - the Google Privacy Policy and Terms of Service apply.
Checkout as a new customer
Creating an account has many benefits:
(0)
Free Shipping (USA)
Free Tech Support
Free 2-Year Warranty
Free shipping to the lower 48 states for online orders of $99 and up.
Our friendly and knowledgeable sales team is here to support you before, during and after your purchase.
We add an extra year to the manufacturer's warranty, giving you a full 2-years coverage - for free!
In stock
The RTW TouchControl 5 is a Dante based immersive monitor controller with metering. Built on RTW's long and proud legacy of making broadcast-ready monitor controllers, it features a 5" intuitive touchscreen and a small footprint that preserves valuable space at your desktop. It even features RTW standard precision metering with loudness and includes SPL, measured using the built-in microphone. With support for up to 32 Dante channels in and out, TouchControl 5 can handle channel formats from stereo to 22.2. Among the many supported formats you will find 5.1 and 7.1 surround as well as 7.1.4 and 9.1.6 immersive.
Tried, tested, and approved by many broadcast engineers around the world, you find the very same monitor control engine that you might know from our legacy surround monitor controllers. The list is long, but let’s emphasize downmix, DSP-powered speaker calibration (using the internal microphone OR manual set), SPL readout, 4 input sources, speaker set selection (up to 4), solo, cut, swap, phase, mono, dim, mute and test tone generator. The source compare feature lets you toggle between sources for easy comparison and lets you set individual delays for each of the sources. On the output side, you can set up four speaker sets and easily switch between them or you can listen to your work with your favorite headphones using the headphones output.
The SPL meter shows the measured sound pressure level in your room, and you can show SPL either as a bar graph or as a number – or both. The downmix instrument outputs your surround or immersive mix in stereo and mono. The downmixed signal can be monitored on speakers or phones or sent to any destination in your audio network. Each speaker can be muted or soloed, and you can invert polarity. The talkback feature lets you talk to speakers or any destination in your Dante network. LF Boost lets you boost your LFE channels with 10 dB and Surr. Att. attenuates the surround channels with 3 dB.
The speakers in your setup can be calibrated with regards to level, delay and EQ. The support for measurement microphones, the built-in test tone generator and the live-input SPL meter is the optimal tool combination for calibrating your speaker levels to ensure they are perfectly aligned. Each speaker has a DSP section for ultimate control. You can set individual delay, gain and polarity, and a 4-band EQ is available for each speaker in your setup. Calibrated speaker levels can easily be recalled by the press of a knob.
Up to two LFE channels with adjustable crossover frequencies can be adapted to your requirements using the bass management. Full-range speakers and smaller speakers can be finely tuned to each other and operated in the same system, while LP filters for bass-controlled speakers, all-pass filters for other speakers and an additional SUB output channel for formats without LFE is also available.
Metering plays a significant role in any RTW device, as is the case with the TouchControl 5. The PPM metering engine is taken from the high-end TouchMonitor meters, and you get a wealth of ways to tailor your own metering experience, including scales, color settings and more. True Peak metering is of course part of the metering story, as well as VU and ‘British PPM’.
For many years, RTW has taken part of forming the international loudness standards in ITU and EBU. Loudness is key to us, so in TouchControl 5 we have implemented the full loudness engine known from RTW's high end broadcast meters. TouchControl 5 supports all international loudness standards such as EBU R128, ITU-R BS.1770-4/1771-1, ATSC A/85, ARIB, OP-59, AGCOM, CALM, LEQ(M), TASA and SAWA.
The Fader instrument allows level control of any Dante channel in your network, and you can freely configure each fader to control the number of channels you wish. More faders can be combined, so you can control multiple groups of channels, and if you do so, levels are controlled relatively, using TouchControl 5's knob. TouchControl 5's touch screen can of course also be used to control each fader, and you can create up to 4 faders each controlling single channels, stereo-, surround- or immersive formats. Toolbox instruments also include a Talkback feature that lets you talk to any audio channel in you network. Talkback sources include the built-in mic, the external XLR input or any audio network channels.
TouchControl 5 lets you design your own view pages. For each instrument you can decide on size, ratio and placement, and several instruments can be rotated to fit your needs. Buttons can be placed anywhere on the screen, those that are placed in the side bar are available across view pages. Say you want your input selector to be available also on the metering page - just place it in the side bar.
The Routing page lets you route your audio channels to and from TouchControl 5. With support for 32 Dante channels plus the physical I/Os, there is a lot of possibilities. For instance you could use the same channels for monitor control and metering, or split them so metering is independent from monitor control.
* Required Fields
The best gear advice always comes from those who use it the most. That's where you come in! Let the pro audio world hear your voice with a review of the RTW TouchControl 5 Dante-Based Immersive Monitor Controller and Meter . Once you submit your review, please check your email and verify your address to have it posted.
exclamation-circle
